The 5869 also incorporates tamper switches that are activated when the cover is removed, or if the unit is forcibly removed from its installation location. Should be programmed as a 24-hour silent zone type. The difference is that the WXT is a one button panic while the WXT-2 is a two button which requires a two button press to lower false alarms. There are personal panic switches such as the 5802WXT or the 5802WXT-2. Once activated, the 5869 Hold-Up Switch/Transmitter can only be reset by the reset key.īefore mounting the 5869 permanently, perform Go/No Go tests to verify adequate transmitter signal strength at desired mounting location. The Honeywell 5869 panic switch is mainly designed for commercial use but it can be used residentially as well. The security system control panel sends a burglary alarm to the central station when a RF signal is received from an enrolled Hold-Up Switch/Transmitter. When the transmitter is activated, it emits an RF signal to the receiver. It is typically mounted under a counter or money draw for inconspicuous operation. For example, if the panic button has a low battery or goes out of range, a message will be displayed.The Honeywell 5869 is a hold-up switch/transmitter for a finger-operated RF transmitting device. Like many wireless devices, panic buttons can be supervised with the system so that the user will be sure that the device is functioning properly. References to the 5834-4 throughout this document refer to. The 5834-4EN is identical to the 5834-4 except the 5834-4EN has a plated bezel and key ring. Panic buttons can also be programmed to either have the alarm produce an audible siren or to produce no sound so that the device serves as a silent alarm. The 5834-4/5834-4EN key transmitters are portable wireless transmitters for use only with wireless alarm systems that support 5800 Series receivers (ex. Another option is to have the central monitoring station call the user before sending dispatch, in case the button was pressed accidentally. For example, the programming settings may require a panic button to be pressed twice in order to send an alarm signal. There are some different ways that panic buttons can be programmed with a security panel in order to prevent false alarms. This can serve as easily accessible panic button in the event of an unexpected emergency, such as discovering a home break-in while you are still in your car. Product Manuals Videos Subscribe to our newsletter. Honeywell 5834-4EN Wireless Enhanced 4 Button Security Key Fob List Price: 126.00. To enroll the 5869, refer to the respective Security System Control Panel Installation and Setup Guide. Wireless Panic Button List Price: 62.00 Our Price: 44. However, it is common for one of these buttons to be set as a panic button for immediate emergency dispatch. Reseting the Honeywell 5869 Panic Switch is fairly simple, provided you have the proper equipment. Some of these buttons are typically used for other actions, such as arming or disarming the panel. These devices usually include multiple buttons, and they can be conveniently attached to a set of car keys. Some panic buttons come in the form of a wireless keyfob device. This can be good for a place where a fire is likely to occur, such as a kitchen. It is also possible to use a panic button as a fire alarm to immediately alert the fire department in the event of a fire. Some panic buttons can be worn in the form of a necklace or bracelet so that the user can carry around the button with them at all times. For instance, an elderly person might have a panic button that they can press to request immediate medical attention. A person may also have a panic button inside their home so that if there is a break in, they can quickly alert the police before the burglars realize that the authorities are on their way.Ī panic button does not have to be used for calling the police. This will alert the authorities without letting the criminals know. For example, many banks and retail establishments have one or more panic buttons that can be pressed in the event of a robbery. Panic buttons are appropriate for both commercial and residential applications. The type of help that is sent will depend upon how exactly the panic button was programmed with the security system. From there, the central monitoring station will send emergency personnel to the address that they have on file. Once a panic button has been pressed, it will send a signal to the security system, which will in turn send a distress signal to a central monitoring station. To avoid a low battery signal, install the four new batteries in less than 15 seconds. Wait ten seconds, then install four new batteries. Panic buttons are specialized emergency devices that are used to request immediate police, fire or medical help. Honeywell wireless smoke/carbon monoxide (CO) detector - 5800COMBO: View the product manual (PDF 1.91 MB) Remove the old batteries.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |